Modeling concrete wrapped CFRP sheet using ANSYS

Basic Help 

Hi

I hope you feeling Good

Because I Model the Reinforced Concrete Column in Ansys , I Know in this way exist many Problems .

for the first wirk , you must do three steps :

1-Modeling Plain Concrete .

2-Modeling Reinforced Concrete ( If You Want to Model wrapped reinforced Concrete ) .

3-Modeling wrapped Reinforced Concrete .

in the end you must vallidate your model with experimental test .

send me your E-mail that I send you Severals PDF's and Files that in those concrete has been Modeled .

regards .

dear friends

I have problem with reinforced conc column with FRP.

I would realy appriciate it if you could send me those mentioned pdfs.

asfa.mohammad [at] gmail.com 

Best wishes

Dear ALL,

I hoe to receive a copy of those PDFs too.  I am trying to modelslabs wtih FRP rapping.

My email is tarekper [at] yahoo.com (tarekper[at]yahoo[dot]com)

Thanks a lot.

Tarek

Dear Friends,

I hoe to receive a copy of those PDFs too.  I am trying to modelslabs wtih FRP rapping.

My email is Nima178// at //tarekper [at] yahoo.com (yahoo.com)

Thanks a lot.

nima

I would be appreciate if you can send me those pdfs about modelling RC and CFRP in ANSYS

MY e-mail: khalid6_9994 [at] yahoo.co.uk

Thanks 

I have problem with reinforced  column

I would be appreciate if you can send me those pdfs

My email is nmnnax [at] mail.ru

Heyy Could you please send me the pdf's about modelling RC and CFRP. I hope itll solve the problems i have. Me email id is arshbcp [at] gmail.com. I would really appreciate a quick reply. Thank u

 <a href="http://goldia.com/enagement-rings.html">Enagagement Rings</a>

hiii all

i make FEA for my master research, i simulate a prestressed concrete beam with two precast units connected by contact element (CONTA.52). i used solid 65 for concrete modelling and link 8 for for prestressing steel with initial strain, i entered the stress strain curve for the concrete with linear isotropic, concrete and multilinear isotropic in five points as below:strain=0.0004    stress = 12 MpaStrain = 0.001   stress = 30 MpaStrain = 0.0015   stress=37.5 Mpastrain =0.002      stress = 40 Mpastrain = 0.0003   stress = 40 MPai applied the load up to failure, then, i found that at the contact area, the strain =0.003 but the stress = 34 Mpa, however from the stress strain curve which i entered it must be = 40 Mpa.i tried to change the stress strain curve to be the fc'=60 Mpa instead of 40 Mpa(just as a trial). and i applied the same load, i found that the strain at that load = 0.0016 but the stress still = 34 Mpa at the same node i hope if someone helps me, i do not know how i can pass this problem

My work also involves ansys modellinf of frp wrapped colun. please send me also the files.

my mail address is patilbhartiyash [at] yahoo.in (patilbhartiyash[at]yahoo[dot]in)

thanks

dear friend

i am working on GFRP wrapped columns. please send me the related pdf files. my email address is patilbhartiyash [at] yahoo.in (patilbhartiyash[at]yahoo[dot]in)

 thanking you

Dublin college university - Going to university in Dublin? On the vibrant campus of Dublin City University you can study over 100 courses on a wide range of subjects.

I am not working with RFP, but your set-up for reinforced concrete in ANSYS would be very helpful.  Thanks, in advance.  leven.deputy [at] jacobs.com (leven[dot]deputy[at]jacobs[dot]com)

Please send me those files 

My  email is : amamnasr [at] gmail.com

 Regards,

 Ahmed. 

hello

my work related to modeling frp on rc beam .

I would be realy so happy if you send me the related PDFs.

my E-mail is " ali.saberi.83 [at] gmail.com "

thanks.

I appreciate if you can send these files to me too:

Eng_mohamedmady [at] hotmail.com (Eng_mohamedmady[at]hotmail[dot]com)

 Many thanks

hi,

if you can send me the PDF files related to concrete modeling it will help me a lot.

My e-mail id is : sajib.civil [at] gmail.com

thanking you 

SAJIB

hey there,

i really appreciate if u can send me those files also.

email: double.a88 [at] gmail.com 

Thx a lot. Cheers =)

Azim 

Jorge Ramon Parra Michel
Centro de Investigaciones en Óptica A.C
León Guanajuato. Mexico
jrpmichel [at] cio.mx

 the Univesity of Alberta published an exelent ansys tutorial:

http://www.mece.ualberta.ca/tutorials/ansys/

best regards:

Jorge Parra-Michel

sir, i urgently need help for modeling FRP wrapped  reinforced concrete beam for my thesis work. I want to do Finite Element Analysis using ANSYS. I am not able to model reinforced concrete in ANSYS.  So can u please send me related files . My e-mail Id is sichow00 [at] yahoo.com (sichow00[at]yahoo[dot]com).

Dear Sir

I need tutorials for modeling of FRP wrapped beam and 3D fracture growth, evaluation of KI,KIIand KII, so please send me these tutorials at the following id:-

himanshu [at] iitp.ac.in

hpiitp [at] gmail.com

Your help will be appreciate.

Modeling concrete wrapped FRP sheet using ANSYS

can u please help me with some tutorials for the same 

Modeling concrete wrapped FRP sheet using ANSYS

can u please help me with some tutorials for the same 

my mail id is  tris.110787 [at] rediffmail.com 

I have problem with reinforced concret column with FRP. 



I would appriciate it if you could send me those  pdfs. 



nmnmax [at] mail.ru

hany ghazalah

hello,

i am an M.S student my research subject is about high strength concrete columns under eccentric loading, so can you send me a copy of this tutorial, it will help me a lot in my research.

Dear friend,

my e-mail address is:hany_well70 [at] hotmail.com

thank you very match

Hi

I model cube concrete specimen in ansys and want to obtain stress-strain curve under compressive load(40 ton).

but i dont obtain true curve

1:how i have to use load step

2: do i need failure criteria for this

3: what is application read ls file and write ls file in solution

4:do you have any example about model concrete specimen in ansys

my email is: ali_rahmatian2008 [at] yahoo.com

Hello all,

   I am faced with a problem of modelling a reinforced concrete beam wrapped with FRP using ANSYS. Can any one help me out please?

I would appreciate your response about this issue. Thnk ya all

I m facing problem in modelling Reinforced beam in Ansys.I want to run smeared crack approch on it and compared the results available with.Can any one send me the tutorials or any data regarding the modelling of RC beam in ansys.

my email address is ajmal.kfupm [at] gmail.com (ajmal[dot]kfupm[at]gmail[dot]com)

thanks

Hi, I'm supposed to build a model of an RC frame in ANSYS but I'm quite a newbie. So, I'd appreciate if you can send those PDFs to hysteresis_pa[at]hotmail.com.

Thanks!

Hi

I'm supposed to build a model of an RC frame in ANSYS but I'm facing some problems. So, I'd appreciate if you can send those PDFs to            ayon_buet [at] yahoo.com

Regards

ayon

I'm in desperate need for those pdf's too if it's at all possible to get them. My email is anne.nieminen [at] aalto.fi

Hi,

I am n graduate student doing my resarch in non-linear finite element modelling of reinforced concrete members strengthen with CFRP using ANSYS. It would be helpful if you can send me the related pdf files to me. My mail ID is prakashn3 [at] gmail.com

Thank you.

N.Prakash 

please can u send me these pdfs,,i need very urgently,,

thanks

Regards
Vikas sharma 

dear civilmh

i want to model reinforced concrete with FRP in ANSYS,

this is my E-mail: "aut_kh1366 [at] yahoo.com"

 It would be helpful if you can send me the related pdf files.

THANKS

Dear civilmh

Please help me out to model RCC Column/Beam  using ANSYS (v 10,0) and also CFRP wrapping for my Ph.D thesis work. I cant model Reinforced Concrete and dont know how to apply reinforcement. 

My Email address is mashfiq7777 [at] yahoo.com (mashfiq7777[at]yahoo[dot]com)

Thank you.

Mashfiq

hi

i am doing master degree in frp using ansys and i need any thing that can help , can you send these PDFs for me, and anything else about modeling concrete or steel bars or frp would be great,

thanks

my e-mail:civilstudents020 [at] yahoo.com

if somebody have pdf tutorials about modelling of RCC beam column joint or RCC structures in ANSYS , plz send me at bishowkumar [at] yahoo.com; bishowkumarstha [at] gmail.com. it will be  very helpful for me.

Hello Everyone,

 I need to do work on Fiber-Reinforced  Polymer Composites to model in ansys.. I need help to model them in ansys.. Anyone have any helping material.. Kindly mail me at

fakhre85 [at] gmail.com 

Thanks in advance.

Will be grateful, have a good day..

 Regards,

Fakhr-e-alam 

Hi Everyone,

I am currently undertaking my undergraduate thesis on RC column response to blast loading. I would greatly appreciate it if someone could send the Ansys tutorials to my email address as well:

afl_craig [at] hotmail.com

Regards,

mathewcarter 

hi my friends may you share with me your document and tutorial?

tolgayilmazhho [at] gmail.com

thanks in advance... 

hello

i want to modling frp tube fill with concreat in ansys with a failour tsai but i cant i need helppppp

if give me a ansys fail about this you help me

anddd i can not speak english good

Hi, we did one of our project of wrapping of RCC beams using CFRP wrapping strips as well CFRP plates from Fosroc. It was excellent project related to one of oil and gas facility and we successfully strengthened the whole structure. Would appreciate if you can also send me your documents so I can have better insight on modelling techniques. My email id is syedmeesamali [at] yahoo.com       

Thanks and Best regards 

can any one help me , iam  study in master degree my search is analysis of short column under eccentrically load by ansys programe , my email is alimajdlafta [at] yahoo.com ,,,,,, thanks

Hi Mohammad,

 I am doing a research in modeling reinforced concret column in Ansys. I would appreciate if you can provide me with any resources that can lead the way through the process. My email is engnsrnsal [at] yahoo.com (engnsrnsal[at]yahoo[dot]com)

Best Regards,

Nisreen

Everyone wants the pdfs, send an e-mail to "hajsadeghi_civil [at] yahoo.com" and then I will forward the pdfs to him/her.

Good Luck

Mohammad Hajsadeghi,

Hello there,

I have just started my Research on the subject matter for MS Structural Engineering. Problem is that I am not very good at modeling in ANSYS. I would really appreciate if someone could share relevent research on the captioned email address;

fawadbilal2011 [at] gmail.com

i have modelled reinforced concrete beam in ansys but could not bond frp on its one face. kindly, anyone please send me ansys file regarding this, or tell me the steps...

Hi everybody,

Could you please anyone know a website or has documents about modeling reinforced cocnrete structures "beams, slabs, columns,..etc" in the accurate and best way?

I will be appretiate, thanks

Respected Engineers and professors,

                                                I m doing my research work in beam column joint. In that connection i completed the experimental work with hybrid frp wrapping. Now i have to model the beam column joint using ansys software. So please help me to model the beam column joint with hybrid frp wrapping.  My mail id :  victorarul333 [at] gmail.com

 I m doing my research work in experimental  and analytical work with  frp wrapping of R C Beam. Now i have to model the beam using ansys software.  Also i need to know how to assign the GFRP in  the ANSYS Model. So please help me. my mail id is adhyudh [at] gmail.com  Kindly forward me the details please.