ABAQUS/CAE

Dear members,

my question is about how to use the Abaqus CAE eigenvalue for a linear buckling analysis.

I did a linear buckling analysis for a gFRP vertical panel (h:270  thick:20 w:50 cm). I applied a uniform pressure with value 1 on the top of the panel along the Z axis.

Mode 1 gives me an Eigenvalue of 52853 (please see the attachment). I know that in order to obtain the maximum buckling stress I should multiplicate the eigenvalue for the load appied. It means that the value for the buckling stress is 52853 (N/cm2).

Hi all

I am M.Sc. sutdent in Istanbul Technical University and my research subject is comparision of several ductile damage models both computationaly and experimentally.

I am trying to compare ductile damage models such as Freudenthal,Cockroft,Ayada ,Brozzo etc. computationally using ABAQUS and seeking a way to implement these damage models in ABAQUS.

To obtain each models damage result individually should damage model be implemented in ABAQUS or  can a regular tensile test results be used for calculation of damage values.

Could you please advise me for methodolgy to run a simulation to obtain ductile damage values accordng to models mentioned above.

Thanks in advance for your help.

Hakkı ISIK.

Hi,

I am trying to model a double lap shear in ABAQUS. In Abaqus version
6.7 and above, Anand's model can be invoked by editing keywords and
adding necessary data lines  in keyword editor. I am facing some
prblems in running the job analysis and since I am new to working with
ABAQUS, I am not able to solve the problem. The problem is, when I
submit the job the status keeps on showing "Running" without showing
any error or warnings. I have tried all both coarse and finner meshes
so i think there is no problem with convergence. 

Hello,

I am very new to Abaqus so I apologize since I am probably using the incorrect terminology for this and asking a fairly simple question.

I would like to model a laser beam striking a part the part is rotating w.r.t. the beam and I would like to model this. I have already set up Cylindrical coordinate and I just want the beam to sweep the surface following the equation:

Theta = Omega * Time

where:

Theta:= Angular Position

Omega:= Angular Velocity

Time:= Time

Hi all,

 I am working with an orphan mesh of a finger made up of:

1) elastic epidermis layer

2) viscoelastic dermis layer

3) hyperelastic fats layer

4) bone

NLGEOM is turned on.

Tie constraints are used between the layers and the bone 

I wish to make this finger 'touch' a cubic object however the job always fails as it is not able to converge.

Will anyone be able to advise on this matter? 

Hi,

I am modelling installation (Jacking) of concrete pile (rigid body) in soil (Eulerian soil) which involves large deformations.

 For jacked pile contact friction is considered as zero.

Inorder to cope up with large deformation which occur during pile penetration process kinematic contact fomulation is used, this formulation is based of master-slave principle implemented in ABAQUS.

When I run the analysis i am encountering with following error:

Hello everybody, i am new in abaqus, is anyone who knows how to apply periodic boundary conditions, for example for unit cell. The piece of code would be very much appreciated

for example ´

if i have on the left hand side node set NSET1, on the right hand site NSET2 than i should use equation like this for periodic boundary conditions in x-direction?

*EQUATION

NSET1, 1,1, NSET2, 1, 1????

Please help 

Best regards

ABAgirl

Hi,

I am pursuing my master's in Mech. Engg. and working on Abaqus for FEA of components. In one of the analysis, 

I am required to apply cyclic loading on the component to determine the Stresses at the edges. Its a compression

cyclic loading with kinematic hardening taken into account. From the documentation for ABAQUS 6.9.1, I found that

in order to apply kinematic hardening in metals, one must take it as Combined (Isotropic + Kinematic) Hardening.

The two concerns I have about this analysis are:

Greetings,

 I need to know how to specify the step in ABAQUS to perform thermal bucking analysis of shell.

Any comment, suggestion or documentation will be appreciated.

Thanks!

 Hi all.
Nice to meet you  

I have the report on simulation Roll forming process by ABAQUS.

Wish that I can have your valuable comments  

Hallo.

hi i am doing my PG project on plate buckling analysis using abaqus but i struck in initial stage.. to do so please help me...

Dear All,