Basic Help 

Hi

I hope you feeling Good

Because I Model the Reinforced Concrete Column in Ansys , I Know in this way exist many Problems .

for the first wirk , you must do three steps :

1-Modeling Plain Concrete .

2-Modeling Reinforced Concrete ( If You Want to Model wrapped reinforced Concrete ) .

3-Modeling wrapped Reinforced Concrete .

in the end you must vallidate your model with experimental test .

send me your E-mail that I send you Severals PDF's and Files that in those concrete has been Modeled .

regards .

Hi

Thank you for replying

Kindly send me those PDFs. My email address is kapadiac@gmail.com

Thank you

Awaiting your reply

Regards

Chirag Kapadia

dear friends

I have problem with reinforced conc column with FRP.

I would realy appriciate it if you could send me those mentioned pdfs.

asfa.mohammad@gmail.com 

Best wishes

Dear ALL,

I hoe to receive a copy of those PDFs too.  I am trying to modelslabs wtih FRP rapping.

My email is tarekper@yahoo.com

Thanks a lot.

Tarek

Dear Friends,

I hoe to receive a copy of those PDFs too.  I am trying to modelslabs wtih FRP rapping.

My email is Nima178// at //yahoo.com

Thanks a lot.

nima

I would be appreciate if you can send me those pdfs about modelling RC and CFRP in ANSYS

MY e-mail: khalid6_9994@yahoo.co.uk

Thanks 

I have problem with reinforced  column

I would be appreciate if you can send me those pdfs

My email is nmnnax@mail.ru

Heyy Could you please send me the pdf's about modelling RC and CFRP. I hope itll solve the problems i have. Me email id is arshbcp@gmail.com. I would really appreciate a quick reply. Thank u

 <a href="http://goldia.com/enagement-rings.html">Enagagement Rings</a>

hiii all

i make FEA for my master research, i simulate a prestressed concrete beam with two precast units connected by contact element (CONTA.52). i used solid 65 for concrete modelling and link 8 for for prestressing steel with initial strain, i entered the stress strain curve for the concrete with linear isotropic, concrete and multilinear isotropic in five points as below:strain=0.0004    stress = 12 MpaStrain = 0.001   stress = 30 MpaStrain = 0.0015   stress=37.5 Mpastrain =0.002      stress = 40 Mpastrain = 0.0003   stress = 40 MPai applied the load up to failure, then, i found that at the contact area, the strain =0.003 but the stress = 34 Mpa, however from the stress strain curve which i entered it must be = 40 Mpa.i tried to change the stress strain curve to be the fc'=60 Mpa instead of 40 Mpa(just as a trial). and i applied the same load, i found that the strain at that load = 0.0016 but the stress still = 34 Mpa at the same node i hope if someone helps me, i do not know how i can pass this problem

My work also involves ansys modellinf of frp wrapped colun. please send me also the files.

my mail address is patilbhartiyash@yahoo.in

thanks

dear friend

i am working on GFRP wrapped columns. please send me the related pdf files. my email address is patilbhartiyash@yahoo.in

 thanking you

Dublin college university - Going to university in Dublin? On the vibrant campus of Dublin City University you can study over 100 courses on a wide range of subjects.

I am not working with RFP, but your set-up for reinforced concrete in ANSYS would be very helpful.  Thanks, in advance.  leven.deputy@jacobs.com

Please send me those files 

My  email is : amamnasr@gmail.com

 Regards,

 Ahmed. 

hello

my work related to modeling frp on rc beam .

I would be realy so happy if you send me the related PDFs.

my E-mail is " ali.saberi.83@gmail.com "

thanks.

I appreciate if you can send these files to me too:

Eng_mohamedmady@hotmail.com

 Many thanks

hi,

if you can send me the PDF files related to concrete modeling it will help me a lot.

My e-mail id is : sajib.civil@gmail.com

thanking you 

SAJIB

hey there,

i really appreciate if u can send me those files also.

email: double.a88@gmail.com 

Thx a lot. Cheers =)

Azim 

Jorge Ramon Parra Michel
Centro de Investigaciones en Óptica A.C
León Guanajuato. Mexico
jrpmichel@cio.mx

 the Univesity of Alberta published an exelent ansys tutorial:

http://www.mece.ualberta.ca/tutorials/ansys/

best regards:

Jorge Parra-Michel

sir, i urgently need help for modeling FRP wrapped  reinforced concrete beam for my thesis work. I want to do Finite Element Analysis using ANSYS. I am not able to model reinforced concrete in ANSYS.  So can u please send me related files . My e-mail Id is sichow00@yahoo.com.

Dear Sir

I need tutorials for modeling of FRP wrapped beam and 3D fracture growth, evaluation of KI,KIIand KII, so please send me these tutorials at the following id:-

himanshu@iitp.ac.in

hpiitp@gmail.com

Your help will be appreciate.

Modeling concrete wrapped FRP sheet using ANSYS

can u please help me with some tutorials for the same 

Modeling concrete wrapped FRP sheet using ANSYS

can u please help me with some tutorials for the same 

my mail id is  tris.110787@rediffmail.com 

I have problem with reinforced concret column with FRP. 

I would appriciate it if you could send me those  pdfs. 

nmnmax@mail.ru

hany ghazalah

hello,

i am an M.S student my research subject is about high strength concrete columns under eccentric loading, so can you send me a copy of this tutorial, it will help me a lot in my research.

Dear friend,

my e-mail address is:hany_well70@hotmail.com

thank you very match

Hi

I model cube concrete specimen in ansys and want to obtain stress-strain curve under compressive load(40 ton).

but i dont obtain true curve

1:how i have to use load step

2: do i need failure criteria for this

3: what is application read ls file and write ls file in solution

4:do you have any example about model concrete specimen in ansys

my email is: ali_rahmatian2008@yahoo.com

Hello all,

   I am faced with a problem of modelling a reinforced concrete beam wrapped with FRP using ANSYS. Can any one help me out please?

I would appreciate your response about this issue. Thnk ya all

I m facing problem in modelling Reinforced beam in Ansys.I want to run smeared crack approch on it and compared the results available with.Can any one send me the tutorials or any data regarding the modelling of RC beam in ansys.

my email address is ajmal.kfupm@gmail.com

thanks

Hi,
i'm trying to model exactly the same thing. Those materials would be really helpfull for me.
If it's possible, could you send them for me?
diogobem@yahoo.com.br Thanks 

Hi, I'm supposed to build a model of an RC frame in ANSYS but I'm quite a newbie. So, I'd appreciate if you can send those PDFs to hysteresis_pa[at]hotmail.com.

Thanks!

Hi

I'm supposed to build a model of an RC frame in ANSYS but I'm facing some problems. So, I'd appreciate if you can send those PDFs to            ayon_buet@yahoo.com

Regards

ayon

I'm in desperate need for those pdf's too if it's at all possible to get them. My email is anne.nieminen@aalto.fi