iMechanica - ABAQUS Tutorial and Assignment #1 - Comments

I'm a student in the States

Trent Winslow — Thu, 12 Jan 2012 11:37:10 -0500

I'm a student in the States and I am needing an update tutorial site for abaqus. I've read throught this site, but a few of the sites I've looked at are 3 and 4 year old tutorials. I'm looking for help with engineering solids, for car and motorcycle parts . Any suggestions for a good tutorial would be helpful. Thanks

abaqus software

gloriatrack — Tue, 13 Dec 2011 17:16:52 -0500

As Mr. Hegkadette mentioned earlier:

"Abaqus is a comercial package and its cost depends on where you intend
to use e.g., Industry, University, Research centre etc. As far as I
know, there is no way to legally get a trial version of this software
for free. In any case you should consult Abaqus directly."

________________________________________________

Gloria @ www.firsttime-homebuyer-loans.com

abaqus training

gloriatrack — Tue, 13 Dec 2011 17:06:08 -0500

I doubt the kind of learning that you need can be provided via comments here, and that you will get anything complete to your specific needs. It is better to apply to some training, either online or offline. A simple search results for abaqus training point to Simulia Services website. Here is a list of all available courses from them:

http://www.simulia.com/services/course_descriptions.html

Hope this helps a bit... :)

cu fracture toughness

parghazeh — Wed, 16 Nov 2011 03:58:47 -0500

do any one know "Copper" fracture toughness?pure copper.please help me,Thanks .

parghazeh@gmail.com

cu fracture toughness

parghazeh — Mon, 14 Nov 2011 15:47:58 -0500

do any one know "Copper" fracture toughness?pure copper.please help me,Thanks

create a set of a defined reference point

asimkm — Mon, 31 Oct 2011 09:10:09 -0400

Define a reference point at the desired location.

Make a set of the reference point.

Apply the load to this set.

how to apply load on mesh

omhddr — Sun, 30 Oct 2011 02:28:36 -0400

hi to all

how i can apply concentrated load normal to shell element (4sR) without partitioned it?

Abaqus don't use any unit,

luisavilesm — Fri, 14 Oct 2011 11:06:33 -0400

Abaqus don't use any unit, there are global units, so if you use mm you should have consistents unit in every property that you input to the model..

Umats with abaqus

luisavilesm — Thu, 13 Oct 2011 11:44:04 -0400

Hi, I am a studen in civil engineering. I am trying to modelling some earth dams with abaqus, but I have a problem..I need to use subroutines for both materials clay and sand at the same time..How can I do this?..when I work only with one Umat, i don't have problem but when I use two umats the problems appears..anybody can help me?..

I check the manual, tutorials..etc but i can find anything of this..I hope your help

My mail is lanavi017@hotmail.com, if someone want sent me information directly..

Thanks!

evaluation of K and J integral for edge crack plate

Yogesh Sutar — Fri, 07 Oct 2011 01:22:10 -0400

Hello everyone,

When you create the plate in abaqus, I don't understand how you apply a crack and how you have a stress distribution in all the sample. Also how to calculate K and J integral. Can somebody advise me ?

Thanks in advance.

about simulating propagation of cracks in welded structures

A.Brick Chaouche — Sun, 25 Sep 2011 09:22:40 -0400

Hello, IMechanica's mate, you mentioned cohesive zone model, i use this kind in my studies of initiation and propagation of cracks near a weld joints, i want to use ABAQUS to simulate these behaviours, please can you fit me in this field by giving me some advises. thanks

installer of Abaqus software

DukeKim — Tue, 13 Sep 2011 04:58:31 -0400

Could you please send me the installer of Abaqus software? Thanks so much for kidney stones

abaqous

Sarah A. Eassa — Sun, 04 Sep 2011 02:21:20 -0400

can anyone help me in using abaqous in crack propagation?

thanks

Abaqus e_learning

neuromeka — Sun, 28 Aug 2011 15:43:15 -0400

Hi every body;

I look forword help, how about e_learning for Abaqus ?

is there anywhere webinars and online interactive course of Abaqus

and thx for all

ZAOUI Noureddine
Electromechnical Engineer

hardening rule

danielteruna — Mon, 08 Aug 2011 00:39:47 -0400

Dear Lu

I am trying to conduct cyclic simulation of steel material. When I chose combined hardening model

with use parameter, I must input kinematic hardening parameter C1 and gamma1.

Could you explain how to get this parameter from uniaxial tensile test? Besise that at the subroutine cyclic loading

we must input the eqivalent stress and equivalent plastic strain. What are these parameter? If I am not wrong thsese parameters identic with

stress and stress from uniaxial test.?

thank you for your help

daniel

ABAQUS Tutorial and Assignment #1

Nanshu Lu — Mon, 30 Oct 2006 11:28:42 -0500

1-1 ABAQUS Tutorial: Schedule & Proceedings

1-2 Learning ABAQUS: Begin with ABAQUS Command

1-3 Computer Assignment #1: Plate with circular hole

1-4 CAE Example: Having a sense of ABAQUS CAE